Determining the conditions of filling the hydraulic compensator in a piston mortar pump

Автор(и)

  • Volodymyr Vovchenko Полтавський коледж нафти і газу Полтавського національного технічного університету імені Юрія Кондратюка, Ukraine
  • Olexander Malyushitskiy Полтавський національний технічний університет імені Юрія Кондратюка,
  • Ievgen Vasyliev Полтавський національний технічний університет імені Юрія Кондратюка, Ukraine
  • Anatoly Vasyliev Полтавський національний технічний університет імені Юрія Кондратюка, Ukraine

DOI:

https://doi.org/10.20998/2413-4295.2017.23.02

Ключові слова:

education, universities, information environment, information-analytical system, electronic document, electronic archive

Анотація

The article examines the terms of providing saturation of the working chamber in the hydraulic compensator of the mortar pump with the liquid, which is simultaneously washing liquid for construction of the mortar pump with hydraulic compensator of pressure pulsations of solution feeding. The circumstance that in the construction of the mortar pump there is a primitive unit, which lubricates the friction couple – the piston plunger and its cup-type seal, allows to increase its operational life notably, as this pointed out friction couple is the most vulnerable part of a mortar pump. In addition, the washing liquid at the same time functions as power liquid for working efficiency of a hydraulic compensator of the mortar pump. Therefore, potential consumption of the mentioned liquid in case of carrying out flushing functions should not have an adverse effect on general working efficiency of the mortar pump. After we had analyzed operational stages of the mortar pump, we elucidated that at the start of injection period, in case of incomplete admission (filling of working chamber of the pump compensator with liquid), for example, because of liquid leaks, there can occur depression in the working chamber. This is due to the fact that the amount of the mortar mix, which is pumped in delivery steps, will be unequal – smaller, that the amount of liquid, which is displaced by the compensator with supplementary air, which is stipulated by fluid loss. However, depression will not occur if the compensator is filled with air. It lays the foundation for suggesting autoinflation and support of power liquid at desired level in the pressure compensator cavity through the back-flow prevention valve from the charging tank. Impeccable working efficiency of the offered construction has been confirmed by experimental investigation. Except filling the pressure compensator cavity, this construction also affords to check to see the liquid filling level and the wear rate of a cup-type seal in a mortar pump.

Посилання

Hocz, V. I. Betony i budivelni rozchyny: [pidruchnyk]. – K.: KNUBA, 2003, 472.

Rozchyny budivelni. Zahalni tekhnichni umovy: DSTU B V.2.7-23-95. – Zam. HOST 28013-89, HOST 4.233-86. – [Chynnyi vid 01.01.1996]. – K.: Derzhkommistobuduvannia, 1995. – 14 s. – Natsionalnyi standart Ukrainy.

Onyshchenko, O. H., Vasyliev, A. V., Korobko, B. O. Vplyv obiemnoho rozshyrennia rozchynu na efektyvnist roboty rozchynonasosa. Zbirnyk naukovykh prats (haluzeve mashynobuduvannia, budivnytstvo), 1999, 4, 3 – 9.

Koor, M., Vassiljev, A., Koppel, T. Optimization of pump efficiencies with different pumps characteristics working in parallel mode. Advances in Engineering Software, 2016, 101(2), 69–76, doi: 10.1016/j.advengsoft.2015.10.010.

Feys, D., Khayat, K.H., Perez-Schellb, A., Khatib, R. Prediction of pumping pressure by means of new tribometer for highly-workable concrete. Cement and Concrete Composites, 2015, 57, 102–115, doi: 10.1016/j.cemconcomp.2014.12.007.

Hayashi, I., Kaneko, S. Pressure pulsations in piping system excited by a centrifugal turbomachinery taking the damping characteristics into consideration. Journal of Fluids and Structures, 2014, 45, 216–234, doi: 10.1016/j.jfluidstructs.2013.11.012.

Kosky, P., Balmer, R., Keat, W., Wise, G. Chapter 10 – Manufacturing Engineering. Exploring Engineering. Third Edition, 2013, 205–235. doi: 10.1016/b978-0-12-415891-7.00010-8.

Aprianti, E., Shafigh, P., Zawawi, R., Abu Hassan, Z. F. Introducing an effective curing method for mortar containing high volume cementitious materials. Construction and Building Materials, 2016, 107, 365–377. doi: 10.1016/j.conbuildmat.2015.12.100.

Onyshchenko, O. H., Vasyliev, I. A. Prystrii dlia avtomatychnoho zapovnennia hidravlichnoho kompensatora robochoiu ridynoiu. Mizhvuzivskyi zbirnyk (za napriamom «Inzhenerna mekhanika»), 2006, 18, 261–267.

Pedrajas, C., Rahhal, V., Talero, R. Determination of characteristic rheological parameters in Portland cement pastes. Construction and Building Materials, 2014, 51, 484–491. doi: 10.1016/j.conbuildmat.2013.10.004.

Trapote-Barreira, A., Cama, J., Soler, J. M., Lothenbach, B. Degradation of mortar under advective flow: Column experiments and reactive transport modeling. Cement and Concrete Research, 2016, 81, 81–93. doi: 10.1016/j.cemconres.2015.12.002.

Gonçalves, J. P., Tavares, L. M., Toledo Filho, R. D., Fairbairn, E. M. R., Cunha, E. R. Comparison of natural and manufactured fine aggregates in cement mortars. Cement and Concrete Research, 2007, 37 (6), 924–932. doi: 10.1016/j.cemconres.2007.03.009.

Chen, X., Wu, S., Zhou, J. Experimental and modeling study of dynamic mechanical properties of cement paste, mortar and concrete. Construction and Building Materials, 2013, 47, 419–430. doi: 10.1016/j.conbuildmat.2013.05.063

GOST 21616-91. Tenzorezistory. Obshhie tehnicheskie uslovija. – Vzamen GOST 21616-76. Vved. 01.01.92. – M.: Izd-vo standartov, 1991, 16. 15. Vol'mir A.S. Gibkie plastinki i obolochki. – M.: Gostehizdat, 1956, 419.

##submission.downloads##

Як цитувати

Vovchenko, V., Malyushitskiy, O., Vasyliev, I., & Vasyliev, A. (2017). Determining the conditions of filling the hydraulic compensator in a piston mortar pump. Вісник Національного технічного університету «ХПІ». Серія: Нові рішення у сучасних технологіях, (23(1245), 11–15. https://doi.org/10.20998/2413-4295.2017.23.02

Номер

Розділ

Енергетика, машинобудування та технології конструкційних матеріалів